Email:admin@weiweimachinery.com Tel:+8619838691608 WhatsApp:+8619838691608 Address:Gaocunsi, Gaocun Township, Xingyang, Henan, China (Mainland)
Product knowledge
Your current location: Home > News > Product knowledge >
Six Blades at 1,100 rpm: Why a 2 t/h Chopper Cuts Shorter Straw Than a 6 t/h Machine — Weiwei Machinery
Update:2026-11-18 18:00:10    Views:
A 6.5 t/h chopper turns its blade disc at 650 rpm. That is deliberate, because torque has to move a heavy disc through wet corn stalks at two and a half tonnes an hour. But the same geometry produces a longer, rougher cut, and for sheep, goats and rabbits that is the wrong end of the trade-off: they will pick the long pieces out and leave them on the floor.
The 9ZP-2 sits at the other end. Its disc runs at 1,100 rpm, and it carries six moving blades instead of the three or four used on larger frames. More blades, more cuts per revolution, shorter straw. Capacity is 1 to 2.5 tonnes per hour on a 4 kW motor turning at 2,800 rpm, and the whole machine weighs 115 kg with four wheels, so one person can push it between sheds.
The feed roller is solid cast rather than a fabricated tube. On short, dry material a light roller skips and the straw is dragged in unevenly, which shows up as a mix of dust and 5 cm pieces in the same trough. A cast roller grips the layer and feeds it at a constant rate, so the blade meets the same thickness of material on every revolution.
Two smaller details also help. The bearings are UC series, self-aligning and easy to change in a farm workshop. The drive pulley is weighted, which raises inertia and carries the rotor through the moment when a thick bundle enters, instead of dropping speed and stalling the motor.
The honest limit is throughput. Rated capacity is quoted on green material; dry corn stalks run at roughly half that figure, and hard, over-mature stalks half again. The 2.5 t/h figure is also a ceiling, not an average: it assumes continuous, even feeding by two people, and it will not be reached by one person shovelling from a heap.
For a farm running 30 to 80 head, that is usually the right size. For 300 head, the 6.5 or 10 model is the better buy even though the cut is longer, because six tonnes a day cannot be produced by a 2 t/h machine no matter how short the straw. Weiwei builds the whole series on the same principle, from 0.4 t/h to 10 t/h, and the choice should follow daily tonnage and animal type together.
Zhengzhou Weiwei Machinery has manufactured chaff cutters and feed processing equipment in Henan since 1980, with EU CE and ISO 9001 certification and exports to more than 40 countries. For the 9ZP-2 parameter sheet, blade options or a freight quote, contact WhatsApp +8613526462915, email admin@weiweimachinery.com, or visit www.weiweimachinery.com.

weiwei machinery

short cut straw machine

Next:最后一页
Relevant Article Recommended

24 hour hotline

+8619838691608

Contact
Tel:0086 371 63283021
WeChat:13939084108      /  19838691608
WhatsApp:+86 198 3869 1608
Email:admin@weiweimachinery.com
Address:Gaocunsi, Gaocun Township, Xingyang, Henan, China (Mainland)
WeChat: 19838691608 Email:admin@weiweimachinery.com Address:Gaocunsi, Gaocun Township, Xingyang, Henan, China (Mainland)

Hotline:

+8619838691608

Wechat Qrcode

WhatsApp